The great outdoors by Minka Lavery 8997-66 Guide d'installation

Naviguer en ligne ou télécharger Guide d'installation pour Non The great outdoors by Minka Lavery 8997-66. the great outdoors by Minka Lavery 8997-66 Installation Guide Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 1
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
INSTALLATION INSTRUCTIONS
Model # 8997
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARING FOR INSTALLATION (Fig. 1)
1. Shut off power at the circuit breaker (avertissement!
couper le courant au niveau des fusibles ou du
disjoncteur) and remove the old fixture including
mounting hardware.
2. Carefully unpack your new fixture and lay out all the
parts in a clear area. Take care not to misplace any
small parts necessary for installation.
3. Thread the two studs (B) into the pre-drilled holes in
the circular strap (C) spaced the same distance
apart as the holes in the back plate (H), then tighten
with the nut (E). Note: The length of studs (B) into
circular strap (C) may be adjusted if necessary.
4. Attach circular strap (C) (Part#A-020) using
mounting screws (F) (Part#8/32”*1”L) to the outlet
box (A), (Fig 1).
CONNECTION THE WIRES (Fig. 2)
5. Connect the electrical wires as shown in
Fig.2.Making sure that all wire connectors are
secured. If your outlet box has a ground wire (green
or bare copper), connect the fixture’s ground wire to
it. Otherwise, connect the fixture’s ground wire
directly to the circular strap using the green screw
(D) (Part#8/32”*1/3”L) provided.
FINISHING THE INSTALLATION (Fig.1)
6. To prevent moisture from entering the outlet box (A)
and causing a short, use clear silicone sealant to
outline the outside of fixture back plate (H) where it
meets the wall leaving a space at bottom to allow
moisture a means to escape.
7. Align back plate (H) onto stud (B) and secure with
cap nut (G). (Fig 1)
8. At this point, unscrew the screws (I), remove the
cage (J) with the shade to install 1*100W A bulb in
accordance with the fixture specification—DO NOT
EXCEED THE MAXIMUM WATTAGE RATING!
(NOTE: NO BULB INCLUSED) (NE PAS
DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
9. Replace the cage (J) with the shade, secure with the
screws (I).
Your installation is now complete. Return power to the
outlet box and test the fixture.
Fig. 1
BA RE COPPER( GROUND)
Fig.2
FI XTURE
WIRES
WHI T E
BLACK
(HOT)
WIRES
HOUSE
GREEN OR
WHI T E
( NEUTRAL)
WIRES
HOUSE
( GROUND)
COPPER
BARE
FI XTURE
WIRES
BL ACK
WIRES
FI XTURE
GREEN OR
HOUSE
WIRES
Fig 3
Caulking
Back
p
late
Vue de la page 0
1

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Model # 8997 READ AND SAVE THESE INSTRUCTIONS WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER. AVERTISSEMENT! COUPER LE

Commentaires sur ces manuels

Pas de commentaire