The great outdoors by Minka Lavery 72433-261 Manuel d'instructions télécharger pdf

Fig. 4

Caulking

Backplate

INSTALLATION INSTRUCTIONS

Item#72433-261

READ AND SAVE THESE INSTRUCTIONS

A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Fig. 1

Fig. 3

Fig. 2

ASSEMBLING THE FIXTURE (Fig.1)

Insert front glass (K) into door (J), and secure with clips

(L)

2. Insert back glass (M) and side glass (N) into

lamp body

(H) and secure with clips (I).

MOUNTING THE FIXTURE (Fig.2)

Shut off the power at the fuse box or circuit breaker. If

cessary, remove the old fixture, including the mounting

hardware.

Carefully remove the new fixture from the carton and

check that all parts are included as shown in the

illustration.

5. Thread screws (A) into the pre-drilled holes in the

circular

strap (C) spaced the same distance apart as

the holes in

the back plate of the fixture body and s

ecure with hex nut

(B).

6. Attach the circular strap (C) to the junction box using

the

mounting screws (D) (size: #8-32N*L0.5”).The

side of

circular strap (C) marked “GND” must face out.

The support cable is provided to support the weight of

the fixture while wiring. Align the fixture to circular strap

into a slot located on circular strap (C)

. Carefully allow

the support ca

ble to support the weight of the fixture

while wiring. (Fig 2)

CONNECTING THE WIRES (Fig. 3)

At this point, connect the electrical wires as shown in

figure3, making sure that all wire connectors are secured.

If your outlet has a ground wire (green or bare c

opper),

connect the ground wire from the fixture to it. Otherwise,

connect the ground wire from the fixture directly to the

circular strap (C) and secure with the green screw

provided. After wires are connected, tuck them carefully

into the outlet box. with cap nuts (F).

FINISHING THE INSTALLATION (Fig.2)

To prevent moisture from entering the outlet box and

causing a short, use clear silicone sealant to outline the

outside of fixture back plate (E) where it meets the wall

leaving a space at bottom to allow

moisture a means to

escape. (Fig. 4)

10.

Install the light bulbs (not included)

in accordance with

the fixture’s specifications.

(DO NOT EXCEED THE

MAXIMUM WATTAGE RATING!). (

NE PAS

DEPASSER LA PUISSANCE NOMINALE

MAXIMALE!)

Your installation is now complete.

Return power and

test the fixture.

Note: Illustration (Fig.1) (Fig.2

) on this manual is for

installation purposes only. It may or may not be

identical to the fixture purchased.

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Green or

Bare

Copper

(Ground)

HOUSE

WIRES

Green

(Ground)

Set

020

- Circular Strap

- Ground Screw

Mounting Screw*2

Caulking 1
Backplate 1

Résumé du contenu

Page 1 - Backplate

Fig. 4 Caulking Backplate INSTALLATION INSTRUCTIONS Item#72433-261 READ AND SAVE THESE INSTRUCTIONS WA R N I N G ! S H U T P O W E R O F

Commentaires sur ces manuels

Pas de commentaire

The great outdoors by Minka Lavery 72433-261 Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Non The great outdoors by Minka Lavery 72433-261. the great outdoors by Minka Lavery 72433-261 Instructions / Assembly Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non The great outdoors by Minka Lavery 72433-261