The great outdoors by Minka Lavery 72372-615B Manuel d'instructions télécharger pdf

INSTALLATION INSTRUCTIONS

Model # 72372

READ AND SAVE THESE INSTRUCTIONS

WARN I NG ! S HU T P O W E R O F F AT F U S E O R CI R C U I T B RE A K E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Fig 3

Caulking

Backplate

PREPARING FOR INSTALLATION (Fig. 1)

1. Shut off power at the circuit breaker (avertissement!

couper le courant au niveau des fusibles ou du

disjoncteur) and remove the old fixture including

mounting hardware.

2. Carefully unpack your new fixture and lay out all the

parts in a clear area. Take care not to misplace any

small parts necessary for installation.

3. Unscrew the screws (K), and separate the back

plate (H) from cage (L) and remove cap nuts (G).

4. Thread the two studs (B) into the pre-drilled holes in

the circular strap (C) (Part#A-020) spaced the same

distance apart as the holes in the back plate (H),

then tighten with the hex nut (E). Note: The length of

studs (B) into circular strap (C) may be adjusted if

necessary.

5. Align back plate (H) to the outlet box (A) and mark

the location of the wall anchors (I). Insert the wall

anchors.

6. Attach circular strap (C) (Part#A-020) using

mounting screws (F) (Part#8/32”*1”L) to the outlet

box (A) (Fig 1).

CONNECTION THE WIRES (Fig. 2)

7. Connect the electrical wires as shown in Fig.2.

Making sure that all wire connectors are secured. If

your outlet box has a ground wire (green or bare

copper), connect the fixture’s ground wire to it.

Otherwise, connect the fixture’s ground wire directly

to the circular strap using the green screw (D)

(Part#8/32”*1/3”L) provided.

FINISHING THE INSTALLATION (Fig.1)

8. Align back plate (H) onto studs (B) and with cap

nuts (G) and screws (J) into anchors (I). (Fig 1)

9. Install 4*35W / GU10 bulbs (five bulbs included) in

accordance with the fixture specification.—DO NOT

EXCEED THE MAXIMUM WATTAGE RATING! (NE

PAS DEPASSER LA PUISSANCE NOMINALE

MAXIMALE!)

10. Align cage (L) to back plate (H) and secure with

screws (K) (top and bottom).

11. To prevent moisture from entering the outlet box (A)

and causing a short, use clear silicone Sealant to

outline the outside of fixture back plate (H) where it

meets the wall leaving a space at bottom to allow

moisture a means to escape. (Fig 3)

Your installation is now complete. Return power to the

outlet box and test the fixture.

IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A

QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING

AND INSTALLATION.

Set:

Circular Strap

Ground screw(1)

Mounting screws(2)

BARE COPPER(GROUND)

Fig.2

FIXTURE

WIRES

WHITE

BLACK

(HOT)

WIRES

HOUSE

GREEN OR

WHITE

(NEUTRAL)

WIRES

HOUSE

(GROUND)

COPPER

BARE

FIXTURE

WIRES

BLACK

WIRES

FIXTURE

GREEN OR

HOUSE

WIRES

Fig 3

Caulking

Backplate

Fig. 1

INSTALLATION INSTRUCTIONS 1

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Model # 72372 READ AND SAVE THESE INSTRUCTIONS WARN I NG ! S HU T P O W E R O F F AT F U S E O R CI R C U I T B R

Commentaires sur ces manuels

Pas de commentaire

The great outdoors by Minka Lavery 72372-615B Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Non The great outdoors by Minka Lavery 72372-615B. the great outdoors by Minka Lavery 72372-615B Instructions / Assembly [bs] [hr] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non The great outdoors by Minka Lavery 72372-615B